Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
What are your opinions with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't precisely brain surgery, yet it does need solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is readily accessible, the task can move speedily; if you have to open up a wall to get rid of the old tub as well as place the new bath tub, the task is much harder. In either case, the job is within a residence handyman's skills, although you will require a helper to leave the old bathtub and set in the brand-new one. Make sure you have qualified on your own for the job and also are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed job, it is better to think about employing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This post will assist you install a new bath tub in your restroom if you have actually currently purchased a brand-new bathtub and also don't require to transform the arrangement of your previous water system pipelines.
Your tools as well as product list should make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in place in between the tap and also the sink. Protect the tap in position with the maker offered backnut. Once the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Using the two wood boards under its feet, position the bath tub in the required position. The wooden boards are handy in equally spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water system as well as inspect all joints as well as new pipework for leaks and tighten them if required. Fill the bathtub and also examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been made use of a minimum of once as this will resolve it right into its last position.
Preparing for the Installment
To start with, the supporting frame supplied with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about difficulties with dampness and possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealer can fracture rather very early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles making use of waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on A Step-by-Step Guide to Installing a Bathtub, I assumed sharing that chunk was necessary. Sharing is nice. Helping people is fun. Thanks for your time spent reading it.
Top Article
Report this page